Operating and installation instructions
Fridge freezer
KD 12823 S
en - GB
To avoid the risk of accidents
or damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 07 680 530
Contents
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ice cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cooling drinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Freezer tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cool pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Defrosting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Refrigerator section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Freezer section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning the outer casing, the interior and accessories . . . . . . . . . . . . . . . . . . . . 27
Ventilation gaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
After Sales / Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Climate range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Changing the door hinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Aligning the appliance doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Building in the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Guide to the appliance
aOn/Off button
cRefrigerator section temperature
display
bTemperature selector button
dSuper freeze button and
indicator light
4
Guide to the appliance
aButter and cheese compartment
bAdjustable shelves
cEgg tray
dDoor shelf
eCondensate channel and
drain hole
fFruit and vegetable containers
gBottle divider*
hBottle shelf
iFreezer drawers
* Depending on model
5
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and can normally be
recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Rather than just throwing these
materials away, please ensure that they
are recycled.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Take care not to damage the pipework
at the back of it before or during
transportation to an authorised
collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained, and will not leak out into the
environment.
6
Warning and Safety instructions
This appliance is not intended for
~
This appliance complies with all
relevant local and national safety
requirements. Improper use can,
however, present a risk of both
personal injury and material
damage.
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless they
are supervised whilst using it, or have
been shown how to use it correctly by a
person responsible for their safety.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
Safety with children
This appliance is not a toy! To avoid
~
before using it for the first time. They
contain important notes on the
installation, safety, operation and
care of the appliance.
the risk of injury, do not allow children
to play with it or near it, or to play with
the controls. Neither should they be
allowed to swing on the door. Please
supervise young children whilst you are
using it. Older children may only use
the appliance when its operation has
been clearly explained to them and
they are able to use it safely,
Keep these instructions in a safe
place and pass them on to any
future user.
Correct application
recognising the dangers of misuse.
This appliance is not designed for
~
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
– Shops
– Offices and showrooms
– Hostels and guest houses.
It must only be used as a domestic
appliance to cool and store foodstuffs
as well as to store deep frozen food,
freeze fresh food and to prepare ice.
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
appliance.
7
Warning and Safety instructions
Technical safety
room, there is the danger of
combustible gases building up.
Before setting up the appliance,
~
For every 8 g of coolant at least 1 m3 of
room space is required. The amount of
coolant in the appliance is stated on the
data plate inside the appliance.
check it for any externally visible
damage. Do not install and use a
damaged appliance.
A damaged appliance is dangerous.
Safe operation of the appliance is
~
If the connection cable is faulty it must
~
only assured if it has been installed and
connected in accordance with these
operating and installation instructions.
only be replaced by a service technician
authorised by the manufacturer to protect
the user from danger.
Before connecting the appliance,
~
This appliance contains the coolant
~
make sure that the connection data on
the data plate (voltage and connected
load) match the mains electricity
supply.
Isobutane (R600a), a natural gas which
is environmentally friendly. Although it
is flammable, it does not damage the
ozone layer and does not increase the
greenhouse effect. The use of this
coolant has, however, led to a slight
increase in the noise level of the
appliance. In addition to the noise of
the compressor, you might be able to
hear the coolant flowing around the
system. This is unavoidable, but does
not have any adverse effect on the
performance of the appliance.
Care must be taken during the
transportation and installation of the
appliance that no parts of the cooling
system are damaged. Leaking coolant
can damage the eyes.
This data must correspond in order to
avoid the risk of damage to the
appliance. Consult a qualified
electrician if in any doubt.
Do not connect the appliance to the
~
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
In the event of any damage:
- avoid open flames and anything
which creates a spark,
- disconnect from the mains,
- air the room in which the appliance
is located for several minutes and
- contact the Service Department for
advice.
The more coolant there is in an
~
appliance, the larger the room it should
be installed in. In the event of a
leakage, if the appliance is in a small
8
Warning and Safety instructions
The electrical safety of this
The appliance must be isolated from
~
~
appliance can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with current local and national isolated from the electricity supply
the electricity supply during installation,
maintenance and repair work.
The appliance is only completely
safety regulations. It is most important
that this basic safety requirement is
present and tested regularly, and
where there is any doubt, the
when:
– it has been switched off at the socket
and the plug has been withdrawn, or
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for damage or injury caused by the lack
of or inadequacy of an effective
– the fuse from the fused spur
connection unit has been withdrawn,
or
– the mains fuse has been
disconnected, or
earthing system (e.g. electric shock).
– the screw-out fuse has been
removed (in countries where this is
applicable).
Installation, maintenance and
~
repairs may only be carried out by a
suitably qualified and competent
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
Faulty components must only be
~
replaced by genuine Miele original
spare parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
This appliance may only be used in
While the appliance is under
~
~
mobile installations such as ships, if a
risk assessment of the installation has
been carried out by a suitably qualified
engineer.
guarantee, repairs should only be
undertaken by a service technician
authorised by the manufacturer.
Otherwise the guarantee will be
invalidated.
In countries where there are areas
~
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
9
Warning and Safety instructions
Correct use
Do not store cans or bottles
~
containing carbonated drinks or liquids
Never handle frozen food with wet
~
which could freeze in the freezer. The
cans or bottles could explode. Danger
of injury and damage to the appliance.
hands. Your hands may freeze to the
frozen food. Danger of frost burn.
Do not take ice cubes out with your
~
When cooling drinks quickly in the
~
bare hands and never place ice cubes
or ice lollies in your mouth straight from
the freezer.
freezer, make sure bottles are not left in
for more than one hour; otherwise they
could burst, resulting in injury or
damage.
The very low temperature of the frozen
ice or lollies can cause frost burn to the
lips and tongue.
Observe the "use by" dates given on
~
food to avoid the risk of food poisoning.
Storage times will depend on several
factors, including the freshness and
quality of the food as well as the
Do not refreeze thawed or partially
~
thawed food. Defrosted food should be
used up as quickly as possible, as food
soon loses its nutritional value and goes
off. Defrosted food may only be
temperature at which it is stored. Follow
the instructions given on the food
re-frozen after it has been cooked.
manufacturer's packaging regarding
storage conditions and "use-by" dates.
Do not store explosive materials in
~
the appliance or any products
containing propellants (e.g. spray
cans). Thermostats switching on may
produce sparks which could present a
fire hazard. Flammable compounds
could explode.
Do not use sharp edged objects to
~
– remove frost and ice,
– separate frozen foods and remove
ice trays.
They will damage the evaporator,
causing irreversible damage to the
appliance.
Do not operate any electrical
~
equipment (e.g. an electric ice-cream
maker) inside the appliance. Danger of
sparking and explosion.
Do not place electric heaters or
~
candles in the appliance to defrost it.
These can damage the plastic parts.
If storing alcohol with a high
~
percentage proof, make sure it is tightly
closed and stored upright.
Danger of explosion.
10
Warning and Safety instructions
Do not use defrosting sprays or
Disposal of your old appliance
~
de-icers, as they might contain
Before disposing of an old
~
substances which could damage the
plastic parts or which could cause the
build-up of gases and pose a danger to
health.
appliance, first make the door latch or
lock unusable.
This way you will prevent children from
accidentally locking themselves in and
Do not use any oils or grease on the endangering their lives.
~
door seals, as these will cause the
seals to deteriorate and become
porous with time.
Be careful not to damage any part of
~
the pipework whilst awaiting disposal,
e.g. by
Do not store cooking oil in the
~
– puncturing the refrigerant channels
in the evaporator.
refrigerator door. Traces of oil can
cause stress cracks to occur in the
plastic components in the door.
– bending any pipework.
Do not block the ventilation gaps in
– scratching the surface coating.
~
the appliance as this would impair the
efficiency of the appliance, increase the
electricity consumption and could
cause damage to the appliance.
Splashes of refrigerant can damage the
eyes.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
The appliance is designed for use
~
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range
for your appliance is stated on the data
plate inside the appliance.
Installing it in a room with too low an
ambient temperature, e.g. a garage,
can lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
Do not use a steam-cleaning
~
appliance to defrost or clean this
appliance. Steam could reach the
electrical components and cause a
short circuit.
11
How to save energy
Normal energy
Increased energy
consumption
consumption
Installation site
In a ventilated room.
In an enclosed, unventilated room.
In direct sunlight.
Protected from direct sunlight.
Not situated near to a heat source Situated near to a heat source
(radiator, oven).
(radiator, oven).
Where the ideal ambient room
temperature is approx. 20°C.
Where there is a high ambient
room temperature.
Temperature setting with
a thermostat which is
approximate
With a medium setting of 2 to 3.
With a high setting: the lower the
temperature in the compartment,
the higher the energy
(set in stages).
consumption.
Temperature setting with
a thermostat which is
exact to the degree
(digital display).
Cellar section 8 to 12°C
On appliances with winter setting,
please make sure that the winter
setting is switched off when the
ambient temperature is warmer
than 16 °C.
Refrigerator section 4 to 5 °C
PerfectFresh zone just above 0 °C
Freezer section -18°C
Wine storage section 10 to 12 °C
Only open the doors when
Use
Frequent opening of the doors for
necessary and for as short a time long periods will cause a loss of
as possible.
coldness.
Store food in an organised way.
If food is not stored in an
organised way, searching for an
item will mean the door is open for
longer.
Allow hot food and drinks to cool
down before placing them in the
appliance.
Placing hot food in the appliance
will cause the compressor to run
for a long time, as the appliance
will have to work harder to lower
the temperature.
Store food covered or packaged. The evaporation or condensation
of liquids will cause a loss of
coldness in the refrigerator.
Place frozen food in the
refrigerator to defrost.
Do not over-fill the appliance to
allow air to circulate.
Defrosting
Defrost the freezer compartment
when a layer of ice 0.5 cm thick
has built up.
A layer of ice hinders the cold
from reaching the frozen food, and
causes an increase in energy
consumption.
12
Switching on and off
Before using for the first time
Switching off
The stainless steel trim to the interior
shelves and the door shelves has a
layer of protective foil to prevent
scratching during transportation.
^ Press the On/Off button until the
temperature display goes out.
^ Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing-up liquid, and
then dry with a soft cloth.
The interior light will not come on when
you open the door and the cooling
process will be switched off.
^ Carefully remove the protective foil
from the stainless steel trim.
Switching off for longer
periods of time
Important:
To ensure the correct functioning of
the appliance, let it stand for
between 1½ and 2 hours after
transporting it to its final location
before connecting it to the mains.
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
^ switch the appliance off,
^ switch off at the wall socket and
withdraw the plug,
Switching on
^ defrost the appliance,
^ clean the appliance out and
^ leave the doors ajar to air it.
^ Press the On/Off button. The
temperature display will light up.
If, during a long absence, the
appliance is switched off but not
cleaned out and the doors are left
shut, there is a danger of mould and
odours building up inside the
appliance.
The temperature display for the
refrigerator section will show the
required temperature setting.
The appliance will start cooling down
and the interior light in the refrigerator
section will come on if you open the
door.
Allow the appliance to run for a few
hours before placing food in it. This will
ensure that the temperature is
sufficiently low.
13
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
or defrosted food must not be re-frozen.
Food may be re-frozen once it has
been cooked, as the high temperatures
achieved when cooking destroy most
micro-organisms.
Setting the temperature
The temperatures for the refrigerator
and the freezer sections are set with the
temperature selector button.
The temperature in the appliance will
rise:
– the more often the door is opened
and the longer it is kept open,
– the more food that is stored in it,
^ Press the temperature button
repeatedly until the indicator light for
the temperature you want lights up in
the temperature display for the
refrigerator section.
– the warmer the food is which is being
put into it,
– the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
The temperature will be adjusted
continuously with each press of the
button.
When the refrigerator section is set to
5 °C , the freezer section will have an
average temperature of -18 °C.
. . . temperature in the
refrigerator section
Temperature display
We recommend a temperature of 5 °C
The temperature display on the
control panel always shows the
required temperature.
in the middle of the refrigerator.
. . . in the freezer section
To freeze fresh food and to store frozen
food for a long time, a temperature of
-18 °C is required. At this temperature
the growth of micro-organisms is
The temperature can be adjusted from:
1 °C to 9 °C
generally halted. As soon as the
temperature rises above -10 °C, the
micro-organisms become active in the
food again so that it cannot be kept as
long. For this reason, partially defrosted
14
Super freeze
Super freeze
Switching off Super freeze
Switch the Super freeze function on
before putting fresh food into the
freezer.
The Super freeze function will switch off
automatically after approx. 65 hours.
The indicator light will go out and the
appliance will run at normal power
again.
This helps food to freeze quickly and
retain its nutrients, vitamins, flavours
and appearance.
To save energy, the Super freeze
function can be switched off once a
constant temperature of -18°C or
colder has been reached in the freezer.
You should also check the temperature
inside the appliance from time to time.
Super freeze is not necessary:
– when putting in food that is already
frozen.
– when freezing less than 2 kg fresh
food daily.
^ Press the Super freeze button. The
Super freeze indicator light will go
out, and the appliance will continue
to operate at normal power.
Switching on Super freeze
When freezing small quantities of food
in the freezer, the Super freeze function
should be switched on 6 hours
beforehand. When freezing the
maximum load of food the Super
freeze function should be switched on
24 hours beforehand.
^ Press the Super freeze button. The
Super freeze indicator light will come
on.
The appliance works at full power to
lower the temperature in the
appliance.
15
Using the refrigerator efficiently
Different storage zones
Do not store explosive materials in
Due to the natural circulation of the air
in the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
the different zones when placing food
in the appliance.
the appliance or any products
containing propellants (e.g. spray
cans). Danger of explosion.
If storing alcohol with a high
percentage proof, make sure it is
tightly closed, and store upright.
Warmest area
Do not store cooking oil in the
refrigerator door.
The warmest area is in the top section
of the door. Use this for storing butter
and cheese.
Traces of oil can cause stress
cracks to occur in the plastic
components in the door.
Coldest area
Food must not touch the back wall of
the appliance, as it may freeze to
the back wall.
The coldest area in a refrigerator is
directly above the vegetable
containers.
Use this for all delicate and highly
perishable food, e.g.
Food which should not be
stored in a refrigerator
– fish, meat, poultry,
Not all food is suitable for refrigeration.
This includes:
– sausage products, ready meals,
– dishes or baked goods containing
eggs or cream,
– Fruit and vegetables which are
sensitive to cold, such as bananas,
avocado, papaya, passion fruit,
aubergines, peppers, tomatoes and
cucumbers
– fresh dough, cake mixtures, pizza or
quiche dough,
– soft cheese and other dairy
products,
– Fruit which is not yet ripe
– Potatoes
– pre-packed vegetables and other
fresh food with a label stating it
should be kept at a temperature of
approx. 4 °C.
– Some hard cheeses, e.g. Parmesan
16
Using the refrigerator efficiently
When shopping for food
Fruit and vegetables
The freshness of food when first placed Fruit and vegetables may be stored
in the appliance is an important factor
in determining how long it stays fresh.
Time out of the refrigerator e.g. during
transportation should be kept to a
minimum. For example, do not allow
food to stay in a hot car for too long.
Once food has started to deteriorate,
this process cannot be reversed. As
little as two hours outside the
loose in the vegetable containers.
However, you should bear in mind that
aromas and flavours can transfer from
one type of food to another (e.g. carrots
absorb the smell and flavour of onions
very easily). Some food also gives off a
natural gas (ethylene) which speeds up
the rate at which other food perishes.
Some fruit and vegetables react
refrigerator can cause food to start
deteriorating.
strongly to this gas and should not be
stored together.
– Examples of fruit and vegetables
which produce a large amount of
this natural gas are:
Storing food correctly
Store food covered or packaged. This
will prevent food smells from affecting
other foods, food from drying out, and
also any cross-contamination of
Apples, apricots, pears, nectarines,
peaches, plums, avocado, figs,
blueberries, melons and beans.
bacteria. The growth of bacteria, such
as salmonella, can be avoided by
setting the correct temperature and
maintaining good standards of hygiene.
– Examples of fruit and vegetables
which react strongly to the natural
gases given off by other types of
fruit and vegetables are:
Kiwis, broccoli, cauliflower, Brussels
sprouts, mangos, honeydew melons,
apples, apricots, cucumbers,
tomatoes, pears, nectarines and
peaches.
Example: Broccoli should not be
stored with apples, as apples
produce a large amount of natural
gas to which broccoli is very
sensitive. The result is a shorter than
expected storage time for the
broccoli.
17
Using the refrigerator efficiently
Unpacked meats and vegetables
Unpackaged meat and vegetables
should be stored separately. To avoid
any microbiological
cross-contamination, these foods may
only be stored together if they are
wrapped.
Protein rich foods
Please note that foods rich in protein
deteriorate faster than others.
Shellfish, for example, deteriorates
faster than fish, and fish deteriorates
faster than meat.
Meat
Meat should be stored unwrapped.
(Undo wrappings slightly to leave meat
loosely covered, and leave containers
open). This permits air to circulate
around the meat, allowing the surface
to dry slightly, which helps prevent the
growth of bacteria. To prevent the risk
of bacterial cross-contamination, do not
let meat come into direct contact with
other foods.
18
Adjusting the interior fittings
Moving the shelves
The shelves can be adjusted according
to the height of the food.
^ Raise the shelf, and pull it forwards
slightly until the notch at the side is in
line with the shelf support. It can then
be raised or lowered to the required
level.
^ fit the two brackets onto the supports
on either side at the required height,
The raised edge at the back must face
upwards to prevent food from touching
the back of the appliance and freezing
to it.
^ and push the glass shelves in one
after the other.
The shelf with the raised edge must
be at the back.
Stoppers prevent the shelves from
being dislodged by mistake.
Adjusting the door shelf/bottle
shelf
Split shelf
In order to accommodate tall items in
the appliance, one of the shelves is
divided. The front section can be
pushed under the rear section.
^ Push the door/bottle shelf upwards,
then remove it by pulling it forwards.
^ Replace the door/bottle shelf at the
required position. Ensure that it is
securely pushed back into position.
^ Push the rear half of the glass shelf
up slightly from below.
^ At the same time, pull the front half of
the glass shelf forwards slightly and
then push it carefully under the rear
half.
Moving the bottle divider
(depending on model)
The bottle divider can be moved to the
left or right to ensure that bottles are
held securely in position when the door
is opened and shut.
To move the split shelf:
^ Take both halves of the split glass
shelf out,
The bottle divider can be removed
completely (e.g. for cleaning).
^ To do this, push up the front edge of
the bottle divider, and disengage it.
19
Freezing and storing food
Maximum freezing capacity
Storing frozen food
To ensure that fresh food placed in the
freezer freezes through to the core as
quickly as possible, the maximum
freezing capacity must not be
When buying frozen food to store in
your freezer compartment, check
– that the packaging is not damaged,
– the use-by date,
exceeded. The maximum freezing
capacity for freezing within a 24-hour
period is given on the data plate:
"Freezing capacity ....kg/24 hrs".
– the temperature at which the frozen
food is being stored in the shop. The
length of time it can be kept is
The maximum freezing capacity given
on the data plate has been calculated
according to DIN EN ISO 15502 Stan-
dard.
reduced if it has been stored at a
temperature warmer than -18 °C.
^ Buy frozen food once you have
finished the rest of your shopping,
and wrap it in newspaper or use a
cool bag or cool box to transport it.
Freezing fresh food
Fresh food should be frozen as quickly
as possible. This way the nutritional
value of the food, its vitamin content,
appearance and taste are not impaired.
^ Store it in the freezer as soon as
possible.
Never re-freeze partially or fully
defrosted food. Consume defrosted
food as soon as possible as it will
lose its nutritional value and spoil if
left for too long. Defrosted food may
only be re-frozen after it has been
cooked.
Food which takes a long time to freeze
will lose more water from its cells, which
then shrink.
During the defrosting process, only
some of this water is reabsorbed by the
cells; the rest collects around the food.
If food is frozen quickly, the cells have
less time to lose moisture, so they
shrink less. As there is not so much
moisture loss, it is easier for the food to
reabsorb it during the defrosting
process, and very little water collects
around the defrosted food.
20
Freezing and storing food
Home freezing
lightly before freezing, but care
should be taken as the taste of some
spices alters when frozen.
Only freeze fresh food which is in a
good condition.
– Do not place hot foods or drinks in
the freezer. This causes already
frozen food to thaw, and increases
the energy consumption
Hints on home freezing
– The following types of food are
suitable for freezing:
considerably. Allow hot foods and
drinks to cool down before placing
them in the freezer.
Fresh meat, poultry, game, fish,
vegetables, herbs, fresh fruit, dairy
products, pastry, leftovers, egg
yolks, egg whites and a range of
pre-cooked meals.
Packing
^ Freeze food in portions.
– The following types of food are not
suitable for freezing:
Unsuitable packing material
- wrapping paper
- grease-proof paper
- cellophane
Grapes, lettuce, radishes, sour
cream, mayonnaise, eggs in their
shells, onions, whole raw apples and
pears.
- bin bags
– To retain colour, taste and vitamin C,
vegetables should be blanched after
they have been trimmed and
washed.
- plastic carrier bags
Suitable packing material
- plastic freezer film
- freezer bags
To blanch: bring a large saucepan of
water to the boil, immerse the
vegetables in the fast boiling water
for 2-3 minutes, depending on
variety. Remove, and plunge into
ice-cold water to cool quickly. Drain
and pack ready for freezing.
- aluminium foil
- freezer containers
^ Expel as much air as possible from
bags etc. before sealing them, to
prevent freezer-burn on food.
^ Close the packaging tightly with
- rubber bands
– Lean meat freezes better than fatty
meat, and can be stored for
considerably longer.
- plastic clips
- string or bag ties
- freezer tape.
– To prevent chops, steaks, cutlets or
rolled meat from freezing together in
solid blocks when packed, separate
with a sheet of plastic freezer film.
Freezer bags may also be sealed
using home heat sealing kits.
– Do not season fresh foods or
blanched vegetables before
^ Make a note of the contents and the
date of freezing on the packaging.
freezing. Only season cooked food
21
Freezing and storing food
Before placing food in the freezer
When freezing, make sure that food
already frozen does not come into
contact with fresh food being frozen
as this could cause the frozen food
to begin to defrost.
^ When freezing more than 2 kg of
fresh food, switch on the Super
freeze function for some time before
placing the food in the freezer (see
"Super freeze").
This helps food that is already in the
freezer section to stay frozen.
Freezing large items
If you wish to freeze large items such
as a turkey or game, the glass cold
plates between the drawers can also
be removed. To do this:
Placing food in the freezer
Food to be frozen can be placed
anywhere in the freezer.
^ Remove the top two freezer drawers,
and carefully lift and slide out the
glass cold plates.
Large quantities should be placed
directly on the glass cold plates to
freeze the food quickly. To do this first
take out the top two freezer drawers.
When removing the top drawer, make
sure that you do not block the
Defrosting
Frozen food can be defrosted in
different ways:
ventilation slits in the back wall of the
appliance. They are important for
trouble-free operation of the appliance.
– in a microwave oven,
– in an oven using the "Fan" or
"Defrost" setting,
The lowest freezer drawer must always
remain in the appliance.
– at room temperature,
Each drawer and glass cold plate
can take a maximum of 25 kg.
– in the refrigerator (the cold given off
by the frozen food helps to keep the
other food cold),
^ Place the food flat in the bottom of
the freezer drawers or on the glass
cold plates so that it freezes through
to the core as quickly as possible.
– in a steam oven.
Poultry It is particularly important to
observe food hygiene rules when
defrosting poultry. Do not use the liquid
from defrosted poultry. Pour it away
and wash the container it was in, the
sink and your hands. Danger of
salmonella poisoning.
^ Make sure that the packaging and
containers are dry to prevent them
sticking together when frozen.
Fruit should be defrosted at room
temperature in its packaging, or in a
covered bowl.
22
Freezing and storing food
Most vegetables can be cooked while
still frozen. Just put straight into boiling
water or hot fat. The cooking time is
slightly less than that of fresh
vegetables due to changes in the cell
structure.
Freezer tray
The freezer tray is useful for freezing
small items such as berries, herbs and
vegetables. They can be frozen
individually and therefore maintain their
shape when defrosted.
Never re-freeze partially or fully
defrosted food. Consume defrosted
food as soon as possible as it will
lose its nutritional value and spoil if
left for too long. Defrosted food may
only be re-frozen after it has been
cooked.
^ Space the food out loosely on the
tray.
Ice cubes
^ Hang the tray in one of the upper
freezer drawers.
Leave the food for 10-12 hours to
freeze thoroughly on the tray. Transfer it
to a freezer bag or suitable container
once frozen. Place the bag or container
in the freezer drawer.
^ Fill the ice tray three quarters full with
water, and place it in the bottom of
one of the drawers.
^ Once frozen, use a blunt instrument,
for example a spoon handle, to
remove the ice tray from the freezer.
^ Ice cubes can be removed easily
from the tray by twisting the tray
gently or by holding it under cold
running water for a short while.
Cooling drinks
When placing bottles in the freezer
section for rapid cooling, make sure
they are not left in for more than one
hour as they could burst.
23
Freezing and storing food
Cool pack
The cool pack prevents the
temperature in the freezer rising too
quickly in the event of a power cut.
Place the cool pack in the upper
drawer directly on top of food, or in the
freezer tray to save space. The cool
pack will be at its most effective after it
has been in the freezer for approx. 24
hours.
If there is a power cut, place the cool
pack directly on top of the frozen food
in the top drawer so that the food will
be kept cold for as long as possible.
When placing fresh food in the freezer,
use the cool pack to separate the fresh
food from the food which is already
frozen so that the frozen food does not
begin to thaw.
The cool pack can also be used in a
cool bag to keep food or drinks cool for
a short period of time.
24
Defrosting the appliance
Refrigerator section
Freezer section
The refrigerator defrosts automatically.
The freezer section does not defrost
automatically.
Condensate and frost can build up on
the back wall of the refrigerator section
whilst it is in use. You do not need to
remove this, as it will defrost and
evaporate automatically with the
In normal use, ice and frost will form in
the freezer. If allowed to accumulate,
this will impair the efficiency of the
freezer and increase the consumption
of electricity.
warmth generated by the refrigerator.
The condensate is drained away via a
channel and drain hole into an
evaporation system at the back of the
appliance.
Do not scrape ice and frost off as
this can cause damage and render
the appliance unusable.
The freezer section should be defrosted
from time to time. It must be defrosted if
a layer of ice approx. 0.5 cm thick has
accumulated. It is best to defrost when
only very little food or no food at all is
left in the freezer.
Ensure that the condensate channel
and drain hole are kept clean and
are never blocked so that
condensate can flow away without
hindrance.
Before defrosting
^ Switch on the Super freeze function
approx.1 day before defrosting to
ensure frozen food retains its cold
reserve for longer when taken out of
the freezer.
^ Remove the frozen food from the
freezer section and place it in
another freezer or cool box, or wrap it
in several layers of newspaper or
cloths.
^ Store it in a cool place until the
freezer section is ready for use again
^ Take all freezer drawers out of the
freezer section.
25
Defrosting the appliance
To defrost
After defrosting
^ Clean the freezer section and then
dry it thoroughly.
Carry out the defrosting procedure
as quickly as possible if food has
not been placed in another freezer.
The longer the food is left out at
room temperature, the faster it
defrosts.
^ Close the freezer section door, plug
the appliance back into the mains
socket and switch it on using the
On/Off button.
^ Switch on the Super freeze function
so that the appliance can cool down
quickly. The indicator light will come
on.
^ Switch the appliance off using the
On/Off button, switch off at the socket
and remove the plug.
^ Open the freezer section door.
^ Once the freezer section has
reached the required temperature,
place the food back in the freezer
drawers and slide the drawers back
into the freezer section.
To speed up defrosting, two bowls of
hot water (not boiling) with plates
underneath them can be placed in the
appliance. Closing the door in this
instance will help retain the warmth and
speed up the defrosting process.
^ Switch off Super freeze by pressing
the Super freeze button when the
temperature in the freezer is a
constant -18 °C or colder.
^ Use a sponge or towel to soak up the
defrosted water.
The indicator light will go out.
We do not recommend the use of
hot air blowers such as hairdryers
for defrosting your freezer.
Never place electric heaters or
candles in the appliance to defrost
it. These can damage the plastic
parts.
Do not use defrosting sprays or
de-icers, as they could contain
substances which may damage the
plastic parts and which may cause a
build-up of gases and pose a
danger to health.
26
Cleaning and care
^ A range of Miele branded cleaning
agents, including a microfibre
Before cleaning
^ Switch the appliance off, switch off at
the wall socket and withdraw the
plug.
"E-Cloth", is available from the Miele
UK Spare Parts Department, or via
^ Take any food out of the appliance
and store it in a cool place.
Never use cleaning agents
containing abrasive substances
such as sand, soda, acids chlorides
or chemical solvents.
^ Defrost the freezer.
^ Take out any removable parts, e.g.
shelves, for cleaning.
"Non-abrasive" cleaning agents are
also unsuitable as they can cause
matt areas to appear.
Cleaning the outer casing, the
interior and accessories
Do not let water get into the
electronic unit, into the light or into
the ventilation gaps.
Use warm water with a little washing-up
liquid. Wash all accessories and
drawers by hand only. Do not wash in a
dishwasher.
Do not let water get into the
drainage channel and drain hole
when cleaning.
^ Clean the refrigerator section at least
once a month and the freezer section
each time it is defrosted.
Do not use steam cleaning
apparatus to clean the appliance.
Steam could reach the electrical
components and cause a short
circuit.
^ Clean the condensate channel and
drain hole frequently, so that
condensate can drain away
unhindered. Use a straw or similar to
clear the drain if necessary.
The data plate located inside the
appliance must not be removed. It
contains information which is
required in the event of a service
call.
^ After cleaning wipe the outer casing,
interior and accessories with a damp
cloth and dry with a soft cloth. Leave
the doors open to air the appliance
for a short while.
Ventilation gaps
^ The ventilation gaps should be
cleaned on a regular basis with a
brush or vacuum cleaner. A build up
of dust will increase the appliance's
energy consumption.
27
Cleaning and care
Metal grille at the back of the
appliance
After cleaning
^ Replace all shelves and accessories
in the refrigerator section.
The metal grille at the back of the
appliance (heat exchanger) should be
dusted at least once a year. A build-up
of dust will increase the energy
^ Place food back in the refrigerator
section, close the appliance doors,
insert the plug in the socket and
switch the appliance on.
consumption of the appliance.
^ When cleaning the grille, make sure
that the pipework and other
components do not get broken or
damaged in any way.
^ Switch on the Super freeze function
so that the freezer section can cool
down quickly.
^ Once the temperature in the freezer
has reached the required
temperature, place the food back in
the freezer.
Door seals
Do not use any oils or grease on the
door seals. These will cause the
seals to deteriorate and become
porous over time.
^ Switch off Super freeze by pressing
the Super freeze button.
The door seals should be cleaned
regularly with clean water and then
wiped dry with a soft cloth.
28
Problem solving guide
. . . the compressor is switching in
too frequently and for too long.
Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
^ Check whether the ventilation gaps
have been covered over or become
dusty.
^ Check whether the metal grille (heat
exchanger) at the back of the
appliance has become too dusty.
^ The doors have been opened too
frequently, or a large amount of fresh
food has been put in at once for
freezing.
unauthorised work.
What to do if . . .
^ Check that the doors have been
closed properly.
. . . the appliance does not get cool.
^ Check whether the appliance has
been switched on. The temperature
display must be lit up.
^ Check to see whether a thick layer of
ice has built up in the freezer. If it
has, then the freezer section will
need defrosting.
^ Check that the plug is correctly
inserted into the socket and switched
on.
. . . part of the interior side wall feels
warm?
^ Check that the fuse is not defective
and that the mains fuse has not
tripped. If it has, contact the Miele
Service Department.
This is not a fault.
The appliance has an automatic
temperature regulation system which
maintains the optimum temperature
inside both the refrigerator zone and
the freezer zone.
. . . the temperature in the refrigerator
section or freezer section is too low.
^ Set a warmer temperature.
^ The Super freeze function is still on and
the Super freeze indicator light is on.
^ Check that the doors have been
closed properly.
^ Has a large amount of fresh food
been frozen at the same time?
This makes the compressor run for
longer, causing the temperature in
the refrigerator section to fall
automatically.
29
Problem solving guide
. . . the frozen food is thawing
because the freezer section is too
warm.
. . . the Super freeze indicator light
and one of the temperature display
lights are flashing at the same time.
^ Is the room temperature lower than
the ambient temperature for which
the appliance is designed?
There is a fault. Call the Service
Department.
. . . the interior lighting in the
If so, raise the temperature of the
room.
refrigerator section is not working.
^ Was the refrigerator section door left
open for too long? The lighting
switches itself off automatically after
approx. 15 minutes if the door is left
open.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the freezer
section to become too warm.
If this is not the case, then the lamp is
defective.
. . . food has frozen together.
Use a blunt instrument, e.g. a spoon
handle or plastic scraper, to prise it
apart carefully.
^ Disconnect the appliance from the
mains. Switch off at the wall and
withdraw the plug from the socket, or
disconnect the mains fuse or remove
the screw-out fuse in countries where
this is applicable.
. . . . . . there is a thick layer of ice in
the freezer.
^ Check whether the freezer door
closes properly.
^ Defrost and then clean the freezer
section.
Too thick a layer of ice reduces
efficiency and increases energy
consumption.
. . . the door to the freezer section
will not open because it has been
opened and closed too many times in
succession.
^ Grip the lamp cover a at the front
and unhook it at the back.
^ This is not a fault. The suction caused
by opening and closing the door is
preventing the door from opening.
Wait a few minutes and then try
again. It should now open without
force.
^ Unscrew the lamp b and replace it
with a new one.
30
Problem solving guide
Lamp specification:
220 - 240 V, E 14 fitting
See the old lamp for the Wattage
required.
^ Replace the lamp cover a .
. . . the floor of the refrigerator is wet.
The drain hole is blocked.
^ Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature it is advisable not to
open the doors while waiting for the
appliance to be serviced.
31
Noises
Normal noises
What causes them
Brrrrr...
Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....
Click....
A gurgling noise can be heard when coolant is circulating
through the pipes.
Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....
Creak ...
On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectify
What causes them, and what can you do about
them
Rattling, vibrating
The appliance is uneven: Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture: Move it away.
Drawers, baskets or shelves are unstable or sticking: Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other? Separate them.
The transport cable clips are hanging loose at the back of
the appliance: Remove the clips.
32
After Sales / Guarantee
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– your Miele Dealer
or
– Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
delivery. However, you must activate
your cover by calling 0845 365 6640 or
33
Electrical connection
Electrical connection U.K.
Non-rewireable plugs (BS 1363)
All electrical work should be carried out The fuse cover must be re-fitted when
by a suitably qualified and competent changing the fuse, and if the fuse cover
person in strict accordance with current is lost, the plug must not be used until a
local and national safety (BS 7671 in
the UK).
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
The voltage and frequency are given on
the data plate. Please ensure that these
match the household mains supply. The
fuse rating is quoted on the plug.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
(RCD).
WARNING
THIS APPLIANCE MUST BE
EARTHED
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.
34
Installation
Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliance's energy
Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
consumption.
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
This appliance must not be installed
directly next to another refrigerator
or freezer.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.
Further information is available from
your dealer.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
35
Installation
Climate range
Installation
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
^ Remove the cable clip from the back
of the appliance.
^ Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^ Carefully push the appliance into
position with the back against the
wall.
Climate range
Ambient room
temperature
SN
N
+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
+10°C to +38°C
+10°C to +43°C
ST
Aligning the appliance
T
SN-ST
SN-T
Operating in a room which is too cold
will result in the cooling system
switching off for too long, causing the
internal temperature in the appliance to
rise with the risk of frozen food
deteriorating and going off.
^ To align the appliance, adjust the feet
using the spanner supplied.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered over. The air inlet and outlet
must not be covered or blocked in any
way. They should be dusted on a
regular basis.
36
Installation
Appliance dimensions
A
B
C
KD 12823 S
1817 mm
600 mm
631 mm
37
Changing the door hinging
The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
– a cross-slotted screwdriver,
– a flat-bladed screwdriver,
– a selection of Torx screwdrivers,
– a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles:
^ Pull door handle a towards you. Side
section b slides back.
^ Pull side section b out of the guides
on the mounting plate.
^ Undo the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.
^ Remove the cover caps from the
opposite side, and fit them into the
empty holes.
38
Changing the door hinging
To remove the doors:
^ Then fit cover e from the front over
retaining plate f, and slide it over to
the right. The writing must be visible.
Make sure the door shelves are
empty.
^ Remove cover g, then rotate it by
180° and fit it on the opposite side.
^ Close the upper door.
^ Then fit cover e together with
retaining plate f on the opposite
side.
^ Remove cover a by sliding it
forwards from the back and then
lifting it off.
^ Remove cover b by pulling it
upwards.
Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^ Loosen screws d in upper hinge
plate c and pull it upwards and off.
^ Carefully lift the upper door off and
place it to one side.
^ Carefully loosen cover e from above
using a screwdriver and then take it
off together with retaining plate f.
^ Then separate retaining plate f from
cover e, by pushing it slightly to the
left. Then pull the cover forwards and
off.
^ Rotate retaining plate f by 180°.
39
Changing the door hinging
^ Close the lower appliance door.
^ Pull plastic cover h off.
^ Pull the middle hinge pin i upwards
to remove it.
^ Carefully lift the lower door off and
place it to one side.
^ Remove cap l from the bearing
bush in the door and refit on the
opposite side.
^ Pull cover j off.
^ Remove spring clamp m from
underneath the door and fit it on the
opposite side.
^ Unscrew hinge plate k, turn it
through 180° and fit it on the opposite
side.
^ Turn plastic cover h 180° and refit it
in the centre of hinge plate k.
^ Refit cover j on the opposite side.
40
Changing the door hinging
Changing over the doors:
^ Screw hinge plate e into position on
the opposite side using the two outer
long slots only. Do not use the middle
hole because you will not be able to
align the door later on.
^ Remove cover a by pulling it
forwards.
^ With the help of another person,
carefully tilt the appliance backwards
and pull hinge pin b out.
^ Using a second person, carefully tip
the appliance backwards and then fit
hinge pin b together with hinge bush
c from below into hinge plate e on
the left hand side.
^ Do not lose hinge bush c.
^ Undo screws d and take hinge plate
e off.
^ Remove cover f and fit it into the
holes on the opposite side.
^ Refit cover a on the left.
^ Place the lower door onto hinge pin
b.
^ Unscrew bearing g from hinge plate
e and screw it into the hole on the
other side of hinge plate e.
^ Close the lower appliance door.
^ Fit hinge pin i into middle hinge
plate k in the lower door.
^ Then fit the top door on middle hinge
pin i.
41
Changing the door hinging
Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^ Fit hinge plate c onto the opposite
side and secure it with screws d.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
^ Fit covers a and b to their opposite
sides.
^ Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.
^ Loosely attach the handle to the
opposite side of the door with the two
front screws b.
Mounting plate c must be positioned
on the side of the door so that when the
door is closed it is flush with the side of
the appliance.
If this is not the case,
^ tighten both grub screws a with a
suitable allen key until mounting plate
c lines up correctly.
^ Then tighten all 4 fixing screws b.
^ Slide the side section of the handle
d into the guides on the mounting
plate until it clicks into place.
42
Changing the door hinging
It is important to check that the side
section of the handle d does not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
Realign mounting plate c with grub
screws a until the mounting plate and
the side section of the handle d are at
the correct angle and the side section
does not touch the door seal when the
door is opened.
43
Aligning the appliance doors
The appliance doors can be aligned
with the housing at a later date.
To align the upper door use the long
outer slots in the middle hinge plate:
In the following illustration the door
is not shown in the closed position to
make it easier to see what happens
next.
To align the lower door use the long
outer slots in the lower hinge plate:
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be refitted.
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be refitted.
44
Building in the appliance
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installed next to a wall d a
distance of approx. 55 mm must be
maintained on the hinge side between
the wall d and the appliance b, so
that the doors and the handles have
sufficient space for opening.
aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box a.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm2 to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
45
46
47
Alteration rights reserved / 1810
KD 12823 S
M.-Nr. 07 680 530 / 01
|