NP03Wi Interactive White Board Kit
SOFTWARE MANUAL
This manual describes installation and
operation procedures of the driver / the
calibration software for NP03Wi Interactive
White Board Kit
1
4. Select“I accept the terms in the License Agreement”and click
“Next ＞”
Displays the selection screen of the installation destination folder.
5. Click [Next>].
After that, follow the displayed instructions to complete installation.
When the installation is complete, an IWB icon is added to the desktop.
3
How to uninstall the software
1. Click [Control Panel] in the start menu, and double-click [Add or Remove Programs].
2. Right-click [NP03Wi IWB] and click [Uninstall] in the list.
After that, follow the displayed instructions to complete uninstallation.
3. When uninstallation is completed properly, reboot the computer.
4
Startup the Software
Preparation:
● First of all, perform setup according to the installation manual enclosed
with NP03Wi.
If the computer and the camera unit are not connected by a USB cable,
the message at right would be displayed on and the software would not
be started up.
● For starting up the software, Microsoft .NET Framework 4 or later is required.
If Microsoft .NET Framework is not installed on the computer, visit the website of Microsoft for download and install it on
the computer.
1. Double click the IWB icon on the desktop.
Driver installation message is displayed on.
Click“OK”and follow the displayed instructions for the sequel operations.
When driver installation is completed properly, IWB Setup Software is automatically launched and
task tray. Clicking this icon, IWB setup menu is displayed on the screen.
icon is created in the
Calibration Menu Display
Indicate connection status of the
camera unit and the computer
Indicate status of the stylus pen.
[Calibrated]: The stylus pen is ready to use
[Not calibrated]: Cannot use the stylus pen because calibration is not performed,
or the trouble shooting is displayed on
Close IWB Setup Menu.
* The software will continue to run.
Switch to the troubleshooting
screen
Perform automatic calibration
Perform manual calibration
Right click
icon in the task tray and select [Exit] for finishing IWB.
5
Performing Calibration
Before starting to use the stylus pen, make sure to perform calibration in order to make the computer to recognize exact
position of the stylus pen.
Automatically calibrate the stylus pen position. Recommend this when easy calibration is
Automatic calibration
preferred.
Manually calibrate the stylus pen position. Recommend this for installing the projector
Manual calibration
permanently or when precise calibration is preferred.
Perform Calibration Automatically [Automatic Calibration]
Click the [Start Automatic] button on the displayed calibration menu.
Projected image on the screen will be switched to the Automatic Calibration Screen.
After five to eight seconds, calibration will be completed and the screen will return to display the projected image.
Note:
• If the message in below is displayed on the screen, refer to the Troubleshooting on page 7 and check if the screen is
installed within the recognition area of the camera and if the camera and the screen get influence of external light.
Perform Calibration Manually [Manual Calibration]
1. Click [Start Manual] button on the displayed calibration menu.
Projected image on the screen is switched to the Manual Calibration Screen and red dot
the screen.
is indicated at the top left on
Press briefly on the red dot to calibrate (see top left)
Press [ESC] to cancel calibration
Press [b] to undo last point
6
2. Press the center of the red dot with the stylus pen.
The red dot is indicated at 25 points in order on the screen.
Press briefly on the red dot to calibrate (see top left)
Press [ESC] to cancel calibration
Press [b] to undo last point
When all points indicated by the red dot are pressed by the stylus pen, calibration is completed and the calibration
completion message is displayed on.
3. Touch
icon in the task tray by the stylus pen.
This message is popped up when calibration is completed properly.
Note:
• When“Auto Run”in the troubleshooting screen is checked, the software starts automatically when the computer is
started up.
• Drawing software is required to use the interactive white board function.
Drawing software cannot be downloaded from our projector support page, prepare commercially available drawing
software.
7
Troubleshooting
You can check the installation condition of the camera unit when the troubleshooting in the IWB setup menu is displayed
on.
Troubleshooting screen
Switch to the calibration menu
Change the stylus pen status.
If clicking / pressing this by the
mouse / the stylus pen when PAUSE
CALIBRATION is indicated on this
button, the stylus pen becomes
unavailable.
If clicking this by the mouse when
RESUME CALIBRATION is indicated
on this button, the stylus pen becomes
ready to use.
Enable/disable the Auto Run
function.
When this function is checked,
the software starts automatically
when the computer is started
up.
• Check the camera recognition area
Press four corners of the projection screen by the stylus pen.
A red square is indicated on the troubleshooting screen and it can be checked all area of the screen surface is in
the camera recognition area.
• Check influence of external light
If the camera and/or the screen is exposed to strong light, it may cause of malfunction because the computer
cannot recognize the stylus pen. If a red square is indicated on the screen without touching the screen by the
stylus pen, it means the camera and/or the screen get influence of external light. In this case, change the place to
install them avoiding to receive direct sunshine or strong light.
Others
The stylus pen does
not work.
• Have the driver and the calibration software been installed on the computer?
• Is the USB cable connected between the computer (type A USB port) and the camera unit
(type B USB port)?
• Does the stylus pen have proper charge?
If red LED is not turned on by pressing the pen tip, charge the stylus pen.
Lines traced with the • Has calibration performed properly?
stylus pen do not
match lines indicated
on the screen.
• If it does not solve the problem by performing automatic calibration, try to perform manual
calibration.
8
|