•
If you are using the Ethernet connection to an external modem, turn off and
unplug the broadband modem. Insert the Ethernet cable from the modem
into the 10/100 WAN port (4) of the DGFV338.
the Ethernet cable from the computer to the router is securely attached at
both ends, and that the computer is turned on.
)NSTALLATION 'UIDE
DGFV338 ProSafe™ Wireless ADSL Modem VPN Firewall Router
Configure the DGFV338 for Internet Access
Note: You can connect to both WAN ports if you are planning on using the WAN
rollover feature, but not necessary otherwise.
Before you begin, be sure you have the configuration parameters from your ISP handy.
b. Insert the Ethernet cable that came with your wireless ADSL gateway into a
LAN port on the router (5) and the other end into the Ethernet port of your
computer.
Start Here
1. LOG IN TO THE WIRELESS ADSL GATEWAY
Follow these instructions to set up your wireless ADSL gateway. You can also
consult the documentation links on the Resource CD or the NETGEAR knowledgebase at
Note: To connect to the firewall, your computer needs to be configured to obtain IP
addresses automatically, which is usually the case.
Your network cables are connected and you are ready to restart your network.
3. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE
has its own user name and password.
Warning: Failure to restart your network in the correct sequence could prevent you
from connecting to the Internet.
Prepare to Install Your Gateway
When prompted, enter admin for the firewall User Name and password for the
firewall password.
a. First, power on the broadband modem (if required). Wait two minutes.
The DGFV338 ProSafe Wireless ADSL Modem VPN Firewall Router can be connected
either via an ADSL connection using the internal modem or connected using an Ethernet
connection through an external modem. Either connection is compatible with the wireless
networking bands.
b. You are now connected to the firewall.
b. Now, power on the DGFV338 by connecting the power supply to your gateway
(6). Wait one minute.
c. Last, turn on your computer.
First, Connect the DGFV338
1. CONNECT THE ANTENNAS TO THE DGFV338.
Attach the antennas supplied with the wireless ADSL gateway as shown in (1) and
(2).
Select Web Support on the main menu for links to the NETGEAR DGFV338
product documentation and support knowledge base. Be aware that the default
configuration login time-out is 5 minutes of inactivity, after which automatic
logout will occur.
2. CONNECT THE CABLES BETWEEN THE DGFV338, THE ISP LINE,
AND A COMPUTER
Power
Wireless
Local Port 8
Test
Internet Ports
d. Check the DGFV338 status lights to verify the following:
a. Connect the DGFV338 using one of the following methods:
•
•
•
Power: The power light should turn solid green. If it does not turn solid
green, see the Troubleshooting section of the full manual.
2. CONNECT TO THE INTERNET
Test: When the router is first turned on, the test light is yellow then goes off.
After two minutes if it is still on, see the Troubleshooting Tips below.
Configure your ISP connection for Internet access based on your WAN port
connection configuration:
WAN: Either the Link/Act light on the 10/100 WAN port or the DSL light
should be lit, depending on the method of connection. If not, make sure the
Ethernet cable is securely attached to the modem and the 10/100 WAN port,
and that the modem is powered on, or that the ADSL line is securely
attached to the gateway and the ADSL outlet.
a. From the Network Configuration main menu, select WAN Settings and then
select either the ADSL ISP Settings tab (for DSL) or the Ethernet ISP Settings
(for 10/100)—or configure both if you connected both WAN ports. Click Auto
Detect for the router to detect your ISP connection, or enter the parameters to
complete the Internet configuration.
2
6
1
5
3
4
•
If you are using a direct ADSL connection, insert the telephone cable
directly into the DSL WAN port (3) of the DGFV338, or
•
LOCAL: A LAN light (such as 8) should be lit. Green on top indicates your
computer is communicating at 100 Mbps. If a LAN light is not lit, check that
b. When finished, click Test to verify that the Internet connection you selected is
active.
|