®
S I M P L Y A M A Z I N G
User’s GUide
SPEED SWEEP
Model Tek100
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
Important Safety Instructions
Warranty
Operating Instructions
REGISTER YOUR PRODUCT
ON THE WEB:
WWW.ORECK.COM
Safety Warning
1. Be sure to use the product in compliance with the contents of this manual, and use
approved Oreck replacement parts.
2. After unpacking, make sure that the appliance is intact with no visible signs of damage
caused during shipping. If damage has occurred, do not use this product. Take it to
an authorized Oreck Clean Home Center for service. All packing materials (plastic
wrapping, cardboard box, etc) are potentially dangerous and must be kept out of
children’s reach.
3. Do not leave this product unattended when power is on.
4. Be sure to keep the air intake free and clear of any large debris which can cause a
blockage in the air flow, impacting overall performance.
5. Be sure to keep the air exhaust outlet free and clear to prevent the risk of the motor
burning out.
6. Do not use this product on uneven floors or surfaces and be careful when cleaning
stairs to prevent this unit from falling down.
7. Keep away from heat sources (such as central heating air vents, ovens, etc.) to prevent
the distortion of plastic parts.
8. Before using this product, please remove any large or sharp matters on the floor in
order to avoid damaging internal parts including the filter and motor.
9. Do not try to pick up wet or other liquid items, which will result in damage to the
motor.
10. Keep any loose clothing items away from moving brush roll.
11. The charger is uniquely designed for the rechargeable Ni-MH battery, rating:
Input: 120V, 60 Hz, 50mA
Output: 9V DC, 280Ma
Class:
2
12. After inserting the plug of the charger into the electrical socket, the power light (green)
will illuminate. Insert the rechargeable battery module, this will cause the charge
indicator light (red) to blink. Battery will be fully charged after 8 hours when red light
is solid (not blinking).
13. Once the battery is fully charged, it can be placed into the unit. Before doing so, be
sure to switch the power “OFF” to prevent any possible electrical charge.
14. The brush roll should be cleaned on a regular basis in order to maintain optimal
performance.
15. The filter inside the dirt cup can simply be washed in warm soapy water and can be
used again after drying.
16. It’s suggested to change the filter every 6-12 months, however this may vary depending
upon use.
2
Warranty
ORECK MANUFACTURING COMPANY: (ORECK gives you the following limited warranty
for this product only if it was originally purchased for use, not resale, from ORECK or an
ORECK Authorized Retail Dealer.)
ORECK will repair or replace, free of charge, to the original purchaser, any part which
is found to be defective in material or workmanship within one (1) year of the date of
purchase.
This limited warranty applies to normal domestic use. Any commercial use of this product
will void this limited warranty.
This limited warranty does not cover the replacement of expendable or consumable parts
such as belts, brushes, bulbs, dirt filters, batteries and other parts subject to normal wear.
This limited warranty does not apply to any part subjected to accident, abuse, commercial
use, alteration, misuse, damage caused by fire or act of God, the use of voltages other than
indicated on the serial number plate of this product or service of this product by other than
ORECK or an ORECK Factory Authorized Service Center.
ORECK does not authorize any person or representative to assume or grant any other
warranty obligation with the sale of this product.
ORECK’s limited warranty is valid only if you retain proof of purchase from ORECK or an
ORECK Authorized Retail Dealer for this product. If you purchase this product from any
other source, your purchase is “AS IS,” which means ORECK grants you no warranty, and
that you, not ORECK, assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any defects.
ORECK’s liability for damages to you for any costs whatsoever arising out of this statement
of limited warranty shall be limited to the amount paid for this product at the time of original
purchase, and ORECK shall not be liable for any direct, indirect, consequential or incidental
damages arising out of the use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties, so the above
limitation may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
3
Parts & Accessories List
1. Handle
2. Upholstery brush
3. Crevice tool
1
4. Accessory hook
5. Handle button
2
6. Battery release button
7. Battery compartment
8. Power button
2
3
4
9. Carry handle
10. Dirt Cup
5
11. Roller brush release button
12. Roller brush
7
8
13. Dirt cup release button
6
9
10
11
13
12
4
Assembly Instructions
Before assembling, please be sure that all parts and accessories are
included by reviewing the Parts and Accessories List.
Dirt Cup Assembly
As is shown in the Figure below, place the toll bar of the dust barrel on the back
of the unit, and press down the dirt cup. When the front-end hook on the dirt cup
is placed into the corresponding part on the unit completely, press firmly until a
“click” is heard confirming it is securely in place. To remove the dirt cup, simply
grasp the bottom end of the dirt cup and press the release button, while pulling
away from the unit.
DIrT CUP rELEASE BUTTOn
Emptying the Dirt Cup
After removing the dirt cup as described above, you can now empty its contents.
HAnDLE Of DIrT CUP fILTEr
5
Assembly Instructions
Assembly of roller Brush
As is shown in the figure below, carefully insert the roller brush into the unit, making
sure to align within the specific guide slots and ensuring electric contacts are fully
aligned.
ELECTrICAL COnTACTS
GUIDE SLOTS
Assembly of the Handle
As shown below, pressing the handle release button will allow for the handle to be
removed from the main unit. To reinstall, simply reinsert the handle making sure
the guide slots line up.
HAnDLE rELEASE BUTTOn
6
Assembly Instructions
Operation
1. It is necessary for the rechargeable battery to be fully charged prior to use.
2. The charger is uniquely designed for the rechargeable Ni-MH battery, rating:
Input: 120V, 60 Hz, 50mA; Output: 9V DC, 280Ma; Class: 2
3. After inserting the plug of the charger into the electrical socket, the power light
(green) will illuminate. Insert the rechargeable battery module, this will cause
the charge indicator light (red) to blink. Battery will be fully charged after
8 hours when red light is solid (not blinking).
4. Once the battery is fully charged, it can be placed into the unit. Before doing
so, be sure to switch the power “OFF” to prevent any possible electrical
discharge.
BATTEry
BATTEry
CHArGEr
Battery removal
Removing the rechargeable battery is done by simply pressing the battery release
button located on the side of the unit as shown below.
BATTEry rELEASE BUTTOn
7
Assembly Instructions
Accessory Items
Included with this unit are two accessory items: a crevice tool and upholstery
brush.
A) Crevice Tool
Shown below, the crevice tool is attached for cleaning in tight spaces.
B) Upholstery Brush
With the crevice tool still attached, affix the upholstery brush to the end of the
crevice tool as indicated below.
8
Maintenance
1. Dirt Cup filter
After emptying the dirt cup as described above, the filter can also be cleaned
at the same time. By grasping the filter screen guard in one hand, use the
opposite hand to rotate the handle as indicated by the arrow direction shown
on the top of the filter. Once removed, the filter can be shaken off to remove
any collected debris.
fILTEr SCrEEn GUArD
2. Air intake screen
As shown below, the air intake screen can be removed and cleaned in warm
soapy water. Once completely dry, it can be placed back into the unit.
AIr InTAKE SCrEEn
9
Troubleshooting
Problem
Cause
Areas to check
The unit does not work 1. The battery has been
1. Insert the battery
2. Charge the battery
or turn on.
inserted incorrectly
2. The battery has not
been charged
roller brush is not
working
1. Roller brush has
debris wrapped
around it.
1. Remove the roller
brush and thoroughly
clean, then reinsert
back into the unit.
The indicator lamp
(red) does not work
when charging
1. The power cord is not 1. Be sure the power
plugged in.
cord is plugged into
the electrical outlet
2. The battery has not
been securely inserted 2. Secure the battery is
into the charger.
correctly inserted into
the charger.
10
Discarding the Vacuum
Remove the batteries by cutting the connector wires one by one before you discard the
appliance. Do not dispose of batteries with your regular household trash. Dispose of them
in an environmentally safe manner.
Battery Disposal
Remove the batteries by cutting the connector wires one by one before you discard the
appliance. Do not dispose of batteries with your regular household trash. Dispose of them
in an environmentally safe manner.
To preserve natural resources,
please recycle or dispose of
expired battery pack properly.
THIS PRODUCT CONTAINS A NICKEL-METAL HYDRIDE
BATTERY.ITMUSTBEDISPOSEDOFPROPERLY.LOCAL,
STATE, OR FEDERAL LAWS MAY PROHIBIT DISPOSAL
OF NICKEL-METAL HYDRIDE BATTERIES IN ORDINARY
TRASH. CONSULT YOUR LOCAL WASTE AUTHORITY
FOR
INFORMATION
REGARDING
AVAILABLE
RECYCLING AND/OR DISPOSAL OPTIONS. FOR
DISPOSAL INFORMATION, CALL THE RECHARGEABLE
BATTERY RECYCLING CORPORATION AT 1-800-8-
BATTERY.
WARNING:
Upon removal, cover the battery pack’s terminals with
heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its components.
Nickel-metal hydride batteries must be recycled or disposed
of properly. Also, never touch both terminals with metal
objects and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these warnings
could result in fire and/or serious injury.
©2009 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used
under the authority of Oreck Holdings, LLC. Printed in America
75851-01 REV A
8/09 ECN# R-9480
|