PTO Generator Trailer
ITEM # 165959
For use on 13000, 27500, and
60000 PTOG North Star
Generators or Other PTO
Generators up to 60kW.
P r o v e n P e r f o r m a n c e
M165959A
PLACE MANUAL NAMEPLATE HERE
OWNER’S MANUAL
00641
Any Questions, Comments, or Problems?
Call Customer Service at 1-800-270-0810
Hours: Monday - Friday 7:30 AM to 5:30 PM
Saturday 7:30 to 11:30 AM CST
STEP 1
•
Open hardware bag and separate the components.
FASTENERS (actual size)
1/2-13 Ny-Loc Nut
Qty. 10
1/2-13 X 1.25” Long
Hex Head Bolt Qty. 8
1/2” Flat Washer
Qty. 18
3/8-16 Hex Nut
Qty. 2
3/8-16 Ny-Loc Wing Nut
Qty. 6
1/2-20 X 1.25” Long
Carriage Bolt Qty. 2
3/8” Flat Washer
Qty. 6
MISCELLANEOUS COMPONENTS (not actual size)
Lug Bolts
Qty. 10
Red Reflector
Qty. 2
Amber Reflector
Qty. 2
PTO Implement
Shaft Retainer
Qty. 2
Cord Hooks
Qty. 2
Hitch Pin With Chain
and Lynch Pin
Qty. 1
00672
3
STEP 2
• Remove remaining components from the box. Discard unpainted shipping bracket. Place trailer Base on two
supports at least twelve(12) inches high.
00673
STEP 3
•
Bolt the Axle to the Base with (6) 1/2”-13 x 1.25 hex head bolts, (12) 1/2” flat washers, and (6) 1/2-13 Ny-Loc
nuts.
00674
4
STEP 4
•
Assemble Tongue Arm to Base with (2) 1/2-13 X 1.25” hex head bolts, (4) 1/2 Flat Washers, and (2) 1/2-13
Ny-Loc Nuts. Assemble Tongue to Tongue Arm with (2) 1/2-13 X 1.25 Carriage bolts, (2) 1/2 flat washers,
and (2) 1/2-13 Ny-Loc nuts. Note: The Tongue Arm and Tongue is adjustable to fit many different PTO
Generators and PTO Implement Shafts. You may need to adjust the Tongue to fit your implement shaft. The
Tongue Arm pivots and is adjustable to fit different PTO Generators, if you have a NorthStar PTO Generator
use the center hole.
00675
STEP 5
•
Assembly wheels to hubs with the 10 lug bolts.
00676
5
STEP 6
•
Apply the (2) red reflectors to the rear of the trailer and (2) amber reflectors to front sides of the trailer as
shown. Assemble the (2) cord hooks to the trailer with (2) 3/8-16 hex nuts, (2) 3/8 flat washers, and (2) 3/8-
16 Ny-Loc wing nuts. Assemble the (2) PTO Implement shaft retainer to the trailer with (4) 3/8 flat washers,
and (4) 3/8-16 Ny-Loc wing nuts. Discard any remaining fasteners.
00677
STEP 7
• Mount NorthStar PTO Generators to trailer using one of the three following bolt patterns. For other PTO
Generators you may need to drill mounting holes.
NorthStar Item
NorthStar Item
#165949
#165929
NorthStar Item
#165937A
NorthStar
Item
#165937B &
6
|