INSTALLATION INSTRUCTIONS FOR PART 99-2006
APPLICATIONS
Cadillac CTS 2003-2007
Cadillac SRX 2004-2006
99-2006/
99-2006G
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked DIN Head Units Provision
• Painted To Match Factory Dash
99-2006 = BLACK
99-2006G = GRAY
KIT COMPONENTS
A) Radio Housing • B) DDIN Brackets • C) DDIN Trim Plate • D) ISO Brackets • E) Trim Plate • F) (8) Phillips screws
• (G) Pocket
E
D
B
C
A
G
F
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench
1-800-221-0932
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION
DASH DISASSEMBLY
99-2006
CADILLAC CTS 2003-2007
CADILLAC SRX 2004-2006
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
11:39 PM
Unclip and remove the center air
vent assembly above the radio.
(Figure A)
60
60
3
Open ashtray and remove (1) Phillips
head screw from inside ashtray.
B
Unclip and remove the a/c control/
ashtray assembly below the radio.
(Figure B)
4
5
11:39 PM
Rear View
Remove (4) 10 MM screws securing
the radio to the dash. (Figure C, D)
60
60
D
C
11:39 PM
11:39 PM
1
KIT ASSEMBLY
99-2006
DIN RADIO PROVISION WITH POCKET
A
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
1
Slide the aftermarket head unit into
the cage and secure. (Figure B)
2
3
Slide the supplied pocket into the
B
unused opening.
ISO MOUNT RADIO PROVISION WITH POCKET
A
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
1
Slide the head unit into the radio
opening until the side clips engage.
(Figure B)
2
B
Snap the Trim plate into the Radio
Housing. (Figure B)
3
4
Slide the supplied pocket into the
unused opening.
2
KIT ASSEMBLY
99-2006
DOUBLE DIN RADIO PROVISION
A
Remove the center bar from the 99-
2006 radio housing. (Figure A)
1
2
Attach the corresponding bracket to
the DDIN head unit. (Figure B)
Insert the DDIN trim plate into the
3
radio housing. (Figure C)
B
Position the bracket/radio assembly
to the back of the radio housing and
secure with the (8) Phillips screws
provided. (Figure D)
4
C
D
Rear View
3
KIT ASSEMBLY
99-2006
STACKED DIN HEAD UNITS PROVISION
A
Slide the DIN cages into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
2
Slide the aftermarket head units into
the cages and secure. (Figure B)
B
4
KIT ASSEMBLY
99-2006
FINAL ASSEMBLY
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
A
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
B
C
Tape
D
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
INST992006
1-800-221-0932
Rev. 08-08-08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST99-2006
|